147 lines
6.6 KiB
Plaintext
147 lines
6.6 KiB
Plaintext
// generated by xmr-stak-rx/1.0.5-rx/af03d89/xmr-stak-rx/lin/cpu
|
|
|
|
/*
|
|
* Network timeouts.
|
|
* Because of the way this client is written it doesn't need to constantly talk (keep-alive) to the server to make
|
|
* sure it is there. We detect a buggy / overloaded server by the call timeout. The default values will be ok for
|
|
* nearly all cases. If they aren't the pool has most likely overload issues. Low call timeout values are preferable -
|
|
* long timeouts mean that we waste hashes on potentially stale jobs. Connection report will tell you how long the
|
|
* server usually takes to process our calls.
|
|
*
|
|
* call_timeout - How long should we wait for a response from the server before we assume it is dead and drop the connection.
|
|
* retry_time - How long should we wait before another connection attempt.
|
|
* Both values are in seconds.
|
|
* giveup_limit - Limit how many times we try to reconnect to the pool. Zero means no limit. Note that stak miners
|
|
* don't mine while the connection is lost, so your computer's power usage goes down to idle.
|
|
*/
|
|
"call_timeout" : 10,
|
|
"retry_time" : 30,
|
|
"giveup_limit" : 0,
|
|
|
|
/*
|
|
* Output control.
|
|
* Since most people are used to miners printing all the time, that's what we do by default too. This is suboptimal
|
|
* really, since you cannot see errors under pages and pages of text and performance stats. Given that we have internal
|
|
* performance monitors, there is very little reason to spew out pages of text instead of concise reports.
|
|
* Press 'h' (hashrate), 'r' (results) or 'c' (connection) to print reports.
|
|
*
|
|
* verbose_level - 0 - Don't print anything.
|
|
* 1 - Print intro, connection event, disconnect event
|
|
* 2 - All of level 1, and new job (block) event if the difficulty is different from the last job
|
|
* 3 - All of level 1, and new job (block) event in all cases, result submission event.
|
|
* 4 - All of level 3, and automatic hashrate report printing
|
|
* 10 - Debug level for developer
|
|
*
|
|
* print_motd - Display messages from your pool operator in the hashrate result.
|
|
*/
|
|
"verbose_level" : 4,
|
|
"print_motd" : true,
|
|
|
|
/*
|
|
* Automatic hashrate report
|
|
*
|
|
* h_print_time - How often, in seconds, should we print a hashrate report if verbose_level is set to 4.
|
|
* This option has no effect if verbose_level is not 4.
|
|
*/
|
|
"h_print_time" : 300,
|
|
|
|
/*
|
|
* Manual hardware AES override
|
|
*
|
|
* Some VMs don't report AES capability correctly. You can set this value to true to enforce hardware AES or
|
|
* to false to force disable AES or null to let the miner decide if AES is used.
|
|
*
|
|
* WARNING: setting this to true on a CPU that doesn't support hardware AES will crash the miner.
|
|
*/
|
|
"aes_override" : null,
|
|
|
|
/*
|
|
* LARGE PAGE SUPPORT
|
|
* Large pages need a properly set up OS. It can be difficult if you are not used to systems administration,
|
|
* but the performance results are worth the trouble - you will get around 20% boost. Slow memory mode is
|
|
* meant as a backup, you won't get stellar results there. If you are running into trouble, especially
|
|
* on Windows, please read the common issues in the README and FAQ.
|
|
*
|
|
* On Linux you will need to configure large page support and increase your memlock limit (ulimit -l).
|
|
*
|
|
* To set large page support, add the following to "/etc/sysctl.d/60-hugepages.conf":
|
|
* vm.nr_hugepages=128
|
|
* You WILL need to run "sudo sysctl --system" for these settings to take effect on your system (or reboot).
|
|
* In some cases (many threads, very large CPU, etc) you may need more than 128
|
|
* (try 256 if there are still complaints from thread inits)
|
|
*
|
|
* To increase the memlock (ulimit -l), add following lines to /etc/security/limits.d/60-memlock.conf:
|
|
* * - memlock 262144
|
|
* root - memlock 262144
|
|
* You WILL need to log out and log back in for these settings to take effect on your user (no need to reboot, just relogin in your session).
|
|
*
|
|
* Check with "/sbin/sysctl vm.nr_hugepages ; ulimit -l" to validate
|
|
*
|
|
* Memory locking means that the kernel can't swap out the page to disk - something that is unlikely to happen on a
|
|
* command line system that isn't starved of memory. I haven't observed any difference on a CLI Linux system between
|
|
* locked and unlocked memory. If that is your setup see option "no_mlck".
|
|
*
|
|
*
|
|
* use_slow_memory defines our behaviour with regards to large pages. There are three possible options here:
|
|
* always - Don't even try to use large pages. Always use slow memory.
|
|
* warn - We will try to use large pages, but fall back to slow memory if that fails.
|
|
* no_mlck - This option is only relevant on Linux, where we can use large pages without locking memory.
|
|
* It will never use slow memory, but it won't attempt to mlock
|
|
* never - If we fail to allocate large pages we will print an error and exit.
|
|
*/
|
|
"use_slow_memory" : "warn",
|
|
|
|
/*
|
|
* TLS Settings
|
|
* If you need real security, make sure tls_secure_algo is enabled (otherwise MITM attack can downgrade encryption
|
|
* to trivially breakable stuff like DES and MD5), and verify the server's fingerprint through a trusted channel.
|
|
*
|
|
* tls_secure_algo - Use only secure algorithms. This will make us quit with an error if we can't negotiate a secure algo.
|
|
*/
|
|
"tls_secure_algo" : true,
|
|
|
|
/*
|
|
* Daemon mode
|
|
*
|
|
* If you are running the process in the background and you don't need the keyboard reports, set this to true.
|
|
* This should solve the hashrate problems on some emulated terminals.
|
|
*/
|
|
"daemon_mode" : true,
|
|
|
|
/*
|
|
* Output file
|
|
*
|
|
* output_file - This option will log all output to a file.
|
|
*
|
|
*/
|
|
"output_file" : "",
|
|
|
|
/*
|
|
* Built-in web server
|
|
* I like checking my hashrate on my phone. Don't you?
|
|
* Keep in mind that you will need to set up port forwarding on your router if you want to access it from
|
|
* outside of your home network. Ports lower than 1024 on Linux systems will require root.
|
|
*
|
|
* httpd_port - Port we should listen on. Default, 0, will switch off the server.
|
|
*/
|
|
"httpd_port" : 8080,
|
|
|
|
/*
|
|
* HTTP Authentication
|
|
*
|
|
* This allows you to set a password to keep people on the Internet from snooping on your hashrate.
|
|
* Keep in mind that this is based on HTTP Digest, which is based on MD5. To a determined attacker
|
|
* who is able to read your traffic it is as easy to break a bog door latch.
|
|
*
|
|
* http_login - Login. Empty login disables authentication.
|
|
* http_pass - Password.
|
|
*/
|
|
"http_login" : "",
|
|
"http_pass" : "",
|
|
|
|
/*
|
|
* prefer_ipv4 - IPv6 preference. If the host is available on both IPv4 and IPv6 net, which one should be choose?
|
|
* This setting will only be needed in 2020's. No need to worry about it now.
|
|
*/
|
|
"prefer_ipv4" : true,
|