mirror of
https://github.com/markqvist/Reticulum.git
synced 2024-11-26 23:40:18 +00:00
551 lines
16 KiB
ReStructuredText
551 lines
16 KiB
ReStructuredText
|
|
.. _interfaces-main:
|
|
|
|
********************
|
|
Supported Interfaces
|
|
********************
|
|
|
|
Reticulum supports using many kinds of devices as networking interfaces, and
|
|
allows you to mix and match them in any way you choose. The number of distinct
|
|
network topologies you can create with Reticulum is more or less endless, but
|
|
common to them all is that you will need to define one or more *interfaces*
|
|
for Reticulum to use.
|
|
|
|
The following sections describe the interfaces currently available in Reticulum,
|
|
and gives example configurations for the respective interface types.
|
|
|
|
For a high-level overview of how networks can be formed over different interface
|
|
types, have a look at the :ref:`Building Networks<networks-main>` chapter of this
|
|
manual.
|
|
|
|
.. _interfaces-auto:
|
|
|
|
Auto Interface
|
|
==============
|
|
|
|
The Auto Interface enables communication with other discoverable Reticulum
|
|
nodes over autoconfigured IPv6 and UDP. It does not need any functional IP
|
|
infrastructure like routers or DHCP servers, but will require at least some
|
|
sort of switching medium between peers (a wired switch, a hub, a WiFi access
|
|
point or similar), and that link-local IPv6 is enabled in your operating
|
|
system, which should be enabled by default in almost all OSes.
|
|
|
|
.. code::
|
|
|
|
# This example demonstrates a TCP server interface.
|
|
# It will listen for incoming connections on the
|
|
# specified IP address and port number.
|
|
|
|
[[Default Interface]]
|
|
type = AutoInterface
|
|
interface_enabled = True
|
|
|
|
# You can create multiple isolated Reticulum
|
|
# networks on the same physical LAN by
|
|
# specifying different Group IDs.
|
|
|
|
group_id = reticulum
|
|
|
|
# You can also select specifically which
|
|
# kernel networking devices to use.
|
|
|
|
devices = wlan0,eth1
|
|
|
|
# Or let AutoInterface use all suitable
|
|
# devices except for a list of ignored ones.
|
|
|
|
ignored_devices = tun0,eth0
|
|
|
|
|
|
If you are connected to the Internet with IPv6, and your provider will route
|
|
IPv6 multicast, you can potentially configure the Auto Interface to globally
|
|
autodiscover other Reticulum nodes within your selected Group ID. You can specify
|
|
the discovery scope by setting it to one of ``link``, ``admin``, ``site``,
|
|
``organisation`` or ``global``.
|
|
|
|
.. code::
|
|
|
|
[[Default Interface]]
|
|
type = AutoInterface
|
|
interface_enabled = True
|
|
|
|
# Configure global discovery
|
|
|
|
group_id = custom_network_name
|
|
discovery_scope = global
|
|
|
|
# Other configuration options
|
|
|
|
discovery_port = 48555
|
|
data_port = 49555
|
|
|
|
|
|
.. _interfaces-i2p:
|
|
|
|
I2P Interface
|
|
=============
|
|
|
|
The I2P interface lets you connect Reticulum instances over the
|
|
`Invisible Internet Protocol <https://i2pd.website>`_. This can be
|
|
especially useful in cases where you want to host a globally reachable
|
|
Reticulum instance, but do not have access to any public IP addresses,
|
|
have a frequently changing IP address, or have firewalls blocking
|
|
inbound traffic.
|
|
|
|
Using the I2P interface, you will get a globally reachable, portable
|
|
and persistent I2P address that your Reticulum instance can be reached
|
|
at.
|
|
|
|
To use the I2P interface, you must have an I2P router running
|
|
on your system. The easiest way to acheive this is to download and
|
|
install the `latest release <https://github.com/PurpleI2P/i2pd/releases/latest>`_
|
|
of the ``ì2pd`` package. For more details about I2P, see the
|
|
`geti2p.net website <https://geti2p.net/en/about/intro>`_.`
|
|
|
|
When an I2P router is running on your system, you can simply add
|
|
an I2P interface to reticulum:
|
|
|
|
.. code::
|
|
|
|
[[I2P]]
|
|
type = I2PInterface
|
|
interface_enabled = yes
|
|
connectable = yes
|
|
|
|
On the first start, Reticulum will generate a new I2P address for the
|
|
interface and start listening for inbound traffic on it. This can take
|
|
a while the first time, especially if your I2P router was also just
|
|
started, and is not yet well-connected to the I2P network. When ready,
|
|
you should see I2P base32 address printed to your log file. You can
|
|
also inspect the status of the interface using the ``rnstatus`` utility.
|
|
|
|
To connect to other Reticulum instances over I2P, just add a comma-separated
|
|
list of I2P base32 addresses to the ``peers`` option of the interface:
|
|
|
|
.. code::
|
|
|
|
[[I2P]]
|
|
type = I2PInterface
|
|
interface_enabled = yes
|
|
connectable = yes
|
|
peers = 5urvjicpzi7q3ybztsef4i5ow2aq4soktfj7zedz53s47r54jnqq.b32.i2p
|
|
|
|
It can take anywhere from a few seconds to a few minutes to establish
|
|
I2P connections to the desired peers, so Reticulum handles the process
|
|
in the background, and will output relevant events to the log.
|
|
|
|
**Please Note!** While the I2P interface is the simplest way to use
|
|
Reticulum over I2P, it is also possible to tunnel the TCP server and
|
|
client interfaces over I2P manually. This can be useful in situations
|
|
where more control is needed, but requires manual tunnel setup through
|
|
the I2P daemon configuration.
|
|
|
|
It is important to note that the two methods are *interchangably compatible*.
|
|
You can use the I2PInterface to connect to a TCPServerInterface that
|
|
was manually tunneled over I2P, for example. This offers a high degree
|
|
of flexibility in network setup, while retaining ease of use in simpler
|
|
use-cases.
|
|
|
|
|
|
.. _interfaces-tcps:
|
|
|
|
TCP Server Interface
|
|
====================
|
|
|
|
The TCP Server interface is suitable for allowing other peers to connect over
|
|
the Internet or private IP networks. When a TCP server interface has been
|
|
configured, other Reticulum peers can connect to it with a TCP Client interface.
|
|
|
|
.. code::
|
|
|
|
# This example demonstrates a TCP server interface.
|
|
# It will listen for incoming connections on the
|
|
# specified IP address and port number.
|
|
|
|
[[TCP Server Interface]]
|
|
type = TCPServerInterface
|
|
interface_enabled = True
|
|
|
|
# This configuration will listen on all IP
|
|
# interfaces on port 4242
|
|
|
|
listen_ip = 0.0.0.0
|
|
listen_port = 4242
|
|
|
|
# Alternatively you can bind to a specific IP
|
|
|
|
# listen_ip = 10.0.0.88
|
|
# listen_port = 4242
|
|
|
|
# Or a specific network device
|
|
|
|
# device = eth0
|
|
# port = 4242
|
|
|
|
**Please Note!** The TCP interfaces support tunneling over I2P, but to do so reliably,
|
|
you must use the i2p_tunneled option:
|
|
|
|
.. code::
|
|
|
|
[[TCP Server on I2P]]
|
|
type = TCPServerInterface
|
|
interface_enabled = yes
|
|
listen_ip = 127.0.0.1
|
|
listen_port = 5001
|
|
i2p_tunneled = yes
|
|
|
|
.. _interfaces-tcpc:
|
|
|
|
TCP Client Interface
|
|
====================
|
|
|
|
To connect to a TCP server interface, you would naturally use the TCP client
|
|
interface. Many TCP Client interfaces from different peers can connect to the
|
|
same TCP Server interface at the same time.
|
|
|
|
.. code::
|
|
|
|
# Here's an example of a TCP Client interface. The
|
|
# target_host can either be an IP address or a hostname.
|
|
|
|
[[TCP Client Interface]]
|
|
type = TCPClientInterface
|
|
interface_enabled = True
|
|
target_host = 127.0.0.1
|
|
target_port = 4242
|
|
|
|
It is also possible to use this interface type to connect via other programs
|
|
or hardware devices that expose a KISS interface on a TCP port, for example
|
|
software-based soundmodems. To do this, use the ``kiss_framing`` option:
|
|
|
|
.. code::
|
|
|
|
# Here's an example of a TCP Client interface that connects
|
|
# to a software TNC soundmodem on a KISS over TCP port.
|
|
|
|
[[TCP KISS Interface]]
|
|
type = TCPClientInterface
|
|
interface_enabled = True
|
|
kiss_framing = True
|
|
target_host = 127.0.0.1
|
|
target_port = 8001
|
|
|
|
**Caution!** Only use the KISS framing option when connecting to external devices
|
|
and programs like soundmodems and similar over TCP. When using the
|
|
``TCPClientInterface`` in conjunction with the ``TCPServerInterface`` you should
|
|
never enable ``kiss_framing``, since this will disable internal reliability and
|
|
recovery mechanisms that greatly improves performance over unreliable and
|
|
intermittent TCP links.
|
|
|
|
**Please Note!** The TCP interfaces support tunneling over I2P, but to do so reliably,
|
|
you must use the i2p_tunneled option:
|
|
|
|
.. code::
|
|
|
|
[[TCP Client over I2P]]
|
|
type = TCPClientInterface
|
|
interface_enabled = yes
|
|
target_host = 127.0.0.1
|
|
target_port = 5001
|
|
i2p_tunneled = yes
|
|
|
|
|
|
.. _interfaces-udp:
|
|
|
|
UDP Interface
|
|
=============
|
|
|
|
A UDP interface can be useful for communicating over IP networks, both
|
|
private and the internet. It can also allow broadcast communication
|
|
over IP networks, so it can provide an easy way to enable connectivity
|
|
with all other peers on a local area network.
|
|
|
|
*Please Note!* Using broadcast UDP traffic has performance implications,
|
|
especially on WiFi. If your goal is simply to enable easy communication
|
|
with all peers in your local ethernet broadcast domain, the
|
|
:ref:`Auto Interface<interfaces-auto>` performs better, and is just as
|
|
easy to use.
|
|
|
|
The below example is enabled by default on new Reticulum installations,
|
|
as it provides an easy way to get started and to test Reticulum on a
|
|
pre-existing LAN.
|
|
|
|
.. code::
|
|
|
|
# This example enables communication with other
|
|
# local Reticulum peers over UDP.
|
|
|
|
[[Default UDP Interface]]
|
|
type = UDPInterface
|
|
interface_enabled = True
|
|
|
|
listen_ip = 0.0.0.0
|
|
listen_port = 4242
|
|
forward_ip = 255.255.255.255
|
|
forward_port = 4242
|
|
|
|
# The above configuration will allow communication
|
|
# within the local broadcast domains of all local
|
|
# IP interfaces.
|
|
|
|
# Instead of specifying listen_ip, listen_port,
|
|
# forward_ip and forward_port, you can also bind
|
|
# to a specific network device like below.
|
|
|
|
# device = eth0
|
|
# port = 4242
|
|
|
|
# Assuming the eth0 device has the address
|
|
# 10.55.0.72/24, the above configuration would
|
|
# be equivalent to the following manual setup.
|
|
# Note that we are both listening and forwarding to
|
|
# the broadcast address of the network segments.
|
|
|
|
# listen_ip = 10.55.0.255
|
|
# listen_port = 4242
|
|
# forward_ip = 10.55.0.255
|
|
# forward_port = 4242
|
|
|
|
# You can of course also communicate only with
|
|
# a single IP address
|
|
|
|
# listen_ip = 10.55.0.15
|
|
# listen_port = 4242
|
|
# forward_ip = 10.55.0.16
|
|
# forward_port = 4242
|
|
|
|
|
|
.. _interfaces-rnode:
|
|
|
|
RNode LoRa Interface
|
|
====================
|
|
|
|
To use Reticulum over LoRa, the `RNode <https://unsigned.io/rnode/>`_ interface
|
|
can be used, and offers full control over LoRa parameters.
|
|
|
|
.. code::
|
|
|
|
# Here's an example of how to add a LoRa interface
|
|
# using the RNode LoRa transceiver.
|
|
|
|
[[RNode LoRa Interface]]
|
|
type = RNodeInterface
|
|
|
|
# Enable interface if you want use it!
|
|
interface_enabled = True
|
|
|
|
# Serial port for the device
|
|
port = /dev/ttyUSB0
|
|
|
|
# Set frequency to 867.2 MHz
|
|
frequency = 867200000
|
|
|
|
# Set LoRa bandwidth to 125 KHz
|
|
bandwidth = 125000
|
|
|
|
# Set TX power to 7 dBm (5 mW)
|
|
txpower = 7
|
|
|
|
# Select spreading factor 8. Valid
|
|
# range is 7 through 12, with 7
|
|
# being the fastest and 12 having
|
|
# the longest range.
|
|
spreadingfactor = 8
|
|
|
|
# Select coding rate 5. Valid range
|
|
# is 5 throough 8, with 5 being the
|
|
# fastest, and 8 the longest range.
|
|
codingrate = 5
|
|
|
|
# You can configure the RNode to send
|
|
# out identification on the channel with
|
|
# a set interval by configuring the
|
|
# following two parameters.
|
|
# id_callsign = MYCALL-0
|
|
# id_interval = 600
|
|
|
|
# For certain homebrew RNode interfaces
|
|
# with low amounts of RAM, using packet
|
|
# flow control can be useful. By default
|
|
# it is disabled.
|
|
flow_control = False
|
|
|
|
.. _interfaces-serial:
|
|
|
|
Serial Interface
|
|
================
|
|
|
|
Reticulum can be used over serial ports directly, or over any device with a
|
|
serial port, that will transparently pass data. Useful for communicating
|
|
directly over a wire-pair, or for using devices such as data radios and lasers.
|
|
|
|
.. code::
|
|
|
|
[[Serial Interface]]
|
|
type = SerialInterface
|
|
interface_enabled = True
|
|
|
|
# Serial port for the device
|
|
port = /dev/ttyUSB0
|
|
|
|
# Set the serial baud-rate and other
|
|
# configuration parameters.
|
|
speed = 115200
|
|
databits = 8
|
|
parity = none
|
|
stopbits = 1
|
|
|
|
.. _interfaces-kiss:
|
|
|
|
KISS Interface
|
|
==============
|
|
|
|
With the KISS interface, you can use Reticulum over a variety of packet
|
|
radio modems and TNCs, including `OpenModem <https://unsigned.io/openmodem/>`_.
|
|
KISS interfaces can also be configured to periodically send out beacons
|
|
for station identification purposes.
|
|
|
|
.. code::
|
|
|
|
[[Packet Radio KISS Interface]]
|
|
type = KISSInterface
|
|
interface_enabled = True
|
|
|
|
# Serial port for the device
|
|
port = /dev/ttyUSB1
|
|
|
|
# Set the serial baud-rate and other
|
|
# configuration parameters.
|
|
speed = 115200
|
|
databits = 8
|
|
parity = none
|
|
stopbits = 1
|
|
|
|
# Set the modem preamble.
|
|
preamble = 150
|
|
|
|
# Set the modem TX tail.
|
|
txtail = 10
|
|
|
|
# Configure CDMA parameters. These
|
|
# settings are reasonable defaults.
|
|
persistence = 200
|
|
slottime = 20
|
|
|
|
# You can configure the interface to send
|
|
# out identification on the channel with
|
|
# a set interval by configuring the
|
|
# following two parameters. The KISS
|
|
# interface will only ID if the set
|
|
# interval has elapsed since it's last
|
|
# actual transmission. The interval is
|
|
# configured in seconds.
|
|
# This option is commented out and not
|
|
# used by default.
|
|
# id_callsign = MYCALL-0
|
|
# id_interval = 600
|
|
|
|
# Whether to use KISS flow-control.
|
|
# This is useful for modems that have
|
|
# a small internal packet buffer, but
|
|
# support packet flow control instead.
|
|
flow_control = false
|
|
|
|
.. _interfaces-ax25:
|
|
|
|
AX.25 KISS Interface
|
|
====================
|
|
|
|
If you're using Reticulum on amateur radio spectrum, you might want to
|
|
use the AX.25 KISS interface. This way, Reticulum will automatically
|
|
encapsulate it's traffic in AX.25 and also identify your stations
|
|
transmissions with your callsign and SSID.
|
|
|
|
Only do this if you really need to! Reticulum doesn't need the AX.25
|
|
layer for anything, and it incurs extra overhead on every packet to
|
|
encapsulate in AX.25.
|
|
|
|
A more efficient way is to use the plain KISS interface with the
|
|
beaconing functionality described above.
|
|
|
|
.. code::
|
|
|
|
[[Packet Radio AX.25 KISS Interface]]
|
|
type = AX25KISSInterface
|
|
|
|
# Set the station callsign and SSID
|
|
callsign = NO1CLL
|
|
ssid = 0
|
|
|
|
# Enable interface if you want use it!
|
|
interface_enabled = True
|
|
|
|
# Serial port for the device
|
|
port = /dev/ttyUSB2
|
|
|
|
# Set the serial baud-rate and other
|
|
# configuration parameters.
|
|
speed = 115200
|
|
databits = 8
|
|
parity = none
|
|
stopbits = 1
|
|
|
|
# Set the modem preamble. A 150ms
|
|
# preamble should be a reasonable
|
|
# default, but may need to be
|
|
# increased for radios with slow-
|
|
# opening squelch and long TX/RX
|
|
# turnaround
|
|
preamble = 150
|
|
|
|
# Set the modem TX tail. In most
|
|
# cases this should be kept as low
|
|
# as possible to not waste airtime.
|
|
txtail = 10
|
|
|
|
# Configure CDMA parameters. These
|
|
# settings are reasonable defaults.
|
|
persistence = 200
|
|
slottime = 20
|
|
|
|
# Whether to use KISS flow-control.
|
|
# This is useful for modems with a
|
|
# small internal packet buffer.
|
|
flow_control = false
|
|
|
|
|
|
.. _interfaces-options:
|
|
|
|
Common Interface Options
|
|
========================
|
|
|
|
A number of general options are available on most interfaces.
|
|
These can be used to control various aspects of interface behaviour.
|
|
|
|
|
|
The ``enabled`` option tells Reticulum whether or not
|
|
to bring up the interface. Defaults to ``False``. For any
|
|
interface to be brought up, the ``enabled`` option
|
|
must be set to ``True`` or ``Yes``.
|
|
|
|
The ``outgoing`` option sets whether an interface is allowed
|
|
to transmit. Defaults to ``True``. If set to ``False`` or ``No``
|
|
the interface will only receive data, and never transmit.
|
|
|
|
The ``mode`` option allows selecting the high-level behaviour
|
|
of the interface from a number of options.
|
|
|
|
- The default value is ``full``. In this mode, all discovery,
|
|
meshing and transport functionality is available.
|
|
|
|
- In the ``access_point`` (or shorthand ``ap``) mode, the
|
|
interface will operate as a network access point. In this
|
|
mode, announces will not be automatically broadcasted on
|
|
the interface, and paths to destinations on the interface
|
|
will have a much shorter expiry time. This mode is useful
|
|
for creating interfaces that are mostly quiet, unless when
|
|
someone is actually using them. An example of this could
|
|
be a radio interface serving a wide area, where users are
|
|
expected to connect momentarily, use the network, and then
|
|
disappear again.
|