mirror of
https://github.com/markqvist/Reticulum.git
synced 2024-08-20 06:00:28 +00:00
749 lines
26 KiB
ReStructuredText
749 lines
26 KiB
ReStructuredText
|
|
.. _interfaces-main:
|
|
|
|
********************
|
|
Supported Interfaces
|
|
********************
|
|
|
|
Reticulum supports using many kinds of devices as networking interfaces, and
|
|
allows you to mix and match them in any way you choose. The number of distinct
|
|
network topologies you can create with Reticulum is more or less endless, but
|
|
common to them all is that you will need to define one or more *interfaces*
|
|
for Reticulum to use.
|
|
|
|
The following sections describe the interfaces currently available in Reticulum,
|
|
and gives example configurations for the respective interface types.
|
|
|
|
For a high-level overview of how networks can be formed over different interface
|
|
types, have a look at the :ref:`Building Networks<networks-main>` chapter of this
|
|
manual.
|
|
|
|
|
|
.. _interfaces-auto:
|
|
|
|
Auto Interface
|
|
==============
|
|
|
|
The Auto Interface enables communication with other discoverable Reticulum
|
|
nodes over autoconfigured IPv6 and UDP. It does not need any functional IP
|
|
infrastructure like routers or DHCP servers, but will require at least some
|
|
sort of switching medium between peers (a wired switch, a hub, a WiFi access
|
|
point or similar), and that link-local IPv6 is enabled in your operating
|
|
system, which should be enabled by default in almost all OSes.
|
|
|
|
.. code::
|
|
|
|
# This example demonstrates a TCP server interface.
|
|
# It will listen for incoming connections on the
|
|
# specified IP address and port number.
|
|
|
|
[[Default Interface]]
|
|
type = AutoInterface
|
|
interface_enabled = True
|
|
|
|
# You can create multiple isolated Reticulum
|
|
# networks on the same physical LAN by
|
|
# specifying different Group IDs.
|
|
|
|
group_id = reticulum
|
|
|
|
# You can also select specifically which
|
|
# kernel networking devices to use.
|
|
|
|
devices = wlan0,eth1
|
|
|
|
# Or let AutoInterface use all suitable
|
|
# devices except for a list of ignored ones.
|
|
|
|
ignored_devices = tun0,eth0
|
|
|
|
|
|
If you are connected to the Internet with IPv6, and your provider will route
|
|
IPv6 multicast, you can potentially configure the Auto Interface to globally
|
|
autodiscover other Reticulum nodes within your selected Group ID. You can specify
|
|
the discovery scope by setting it to one of ``link``, ``admin``, ``site``,
|
|
``organisation`` or ``global``.
|
|
|
|
.. code::
|
|
|
|
[[Default Interface]]
|
|
type = AutoInterface
|
|
interface_enabled = True
|
|
|
|
# Configure global discovery
|
|
|
|
group_id = custom_network_name
|
|
discovery_scope = global
|
|
|
|
# Other configuration options
|
|
|
|
discovery_port = 48555
|
|
data_port = 49555
|
|
|
|
|
|
.. _interfaces-i2p:
|
|
|
|
I2P Interface
|
|
=============
|
|
|
|
The I2P interface lets you connect Reticulum instances over the
|
|
`Invisible Internet Protocol <https://i2pd.website>`_. This can be
|
|
especially useful in cases where you want to host a globally reachable
|
|
Reticulum instance, but do not have access to any public IP addresses,
|
|
have a frequently changing IP address, or have firewalls blocking
|
|
inbound traffic.
|
|
|
|
Using the I2P interface, you will get a globally reachable, portable
|
|
and persistent I2P address that your Reticulum instance can be reached
|
|
at.
|
|
|
|
To use the I2P interface, you must have an I2P router running
|
|
on your system. The easiest way to achieve this is to download and
|
|
install the `latest release <https://github.com/PurpleI2P/i2pd/releases/latest>`_
|
|
of the ``i2pd`` package. For more details about I2P, see the
|
|
`geti2p.net website <https://geti2p.net/en/about/intro>`_.
|
|
|
|
When an I2P router is running on your system, you can simply add
|
|
an I2P interface to Reticulum:
|
|
|
|
.. code::
|
|
|
|
[[I2P]]
|
|
type = I2PInterface
|
|
interface_enabled = yes
|
|
connectable = yes
|
|
|
|
On the first start, Reticulum will generate a new I2P address for the
|
|
interface and start listening for inbound traffic on it. This can take
|
|
a while the first time, especially if your I2P router was also just
|
|
started, and is not yet well-connected to the I2P network. When ready,
|
|
you should see I2P base32 address printed to your log file. You can
|
|
also inspect the status of the interface using the ``rnstatus`` utility.
|
|
|
|
To connect to other Reticulum instances over I2P, just add a comma-separated
|
|
list of I2P base32 addresses to the ``peers`` option of the interface:
|
|
|
|
.. code::
|
|
|
|
[[I2P]]
|
|
type = I2PInterface
|
|
interface_enabled = yes
|
|
connectable = yes
|
|
peers = 5urvjicpzi7q3ybztsef4i5ow2aq4soktfj7zedz53s47r54jnqq.b32.i2p
|
|
|
|
It can take anywhere from a few seconds to a few minutes to establish
|
|
I2P connections to the desired peers, so Reticulum handles the process
|
|
in the background, and will output relevant events to the log.
|
|
|
|
**Please Note!** While the I2P interface is the simplest way to use
|
|
Reticulum over I2P, it is also possible to tunnel the TCP server and
|
|
client interfaces over I2P manually. This can be useful in situations
|
|
where more control is needed, but requires manual tunnel setup through
|
|
the I2P daemon configuration.
|
|
|
|
It is important to note that the two methods are *interchangably compatible*.
|
|
You can use the I2PInterface to connect to a TCPServerInterface that
|
|
was manually tunneled over I2P, for example. This offers a high degree
|
|
of flexibility in network setup, while retaining ease of use in simpler
|
|
use-cases.
|
|
|
|
|
|
.. _interfaces-tcps:
|
|
|
|
TCP Server Interface
|
|
====================
|
|
|
|
The TCP Server interface is suitable for allowing other peers to connect over
|
|
the Internet or private IP networks. When a TCP server interface has been
|
|
configured, other Reticulum peers can connect to it with a TCP Client interface.
|
|
|
|
.. code::
|
|
|
|
# This example demonstrates a TCP server interface.
|
|
# It will listen for incoming connections on the
|
|
# specified IP address and port number.
|
|
|
|
[[TCP Server Interface]]
|
|
type = TCPServerInterface
|
|
interface_enabled = True
|
|
|
|
# This configuration will listen on all IP
|
|
# interfaces on port 4242
|
|
|
|
listen_ip = 0.0.0.0
|
|
listen_port = 4242
|
|
|
|
# Alternatively you can bind to a specific IP
|
|
|
|
# listen_ip = 10.0.0.88
|
|
# listen_port = 4242
|
|
|
|
# Or a specific network device
|
|
|
|
# device = eth0
|
|
# port = 4242
|
|
|
|
**Please Note!** The TCP interfaces support tunneling over I2P, but to do so reliably,
|
|
you must use the i2p_tunneled option:
|
|
|
|
.. code::
|
|
|
|
[[TCP Server on I2P]]
|
|
type = TCPServerInterface
|
|
interface_enabled = yes
|
|
listen_ip = 127.0.0.1
|
|
listen_port = 5001
|
|
i2p_tunneled = yes
|
|
|
|
In almost all cases, it is easier to use the dedicated ``I2PInterface``, but for complete
|
|
control, and using I2P routers running on external systems, this option also exists.
|
|
|
|
.. _interfaces-tcpc:
|
|
|
|
TCP Client Interface
|
|
====================
|
|
|
|
To connect to a TCP server interface, you would naturally use the TCP client
|
|
interface. Many TCP Client interfaces from different peers can connect to the
|
|
same TCP Server interface at the same time.
|
|
|
|
The TCP interface types can also tolerate intermittency in the IP link layer.
|
|
This means that Reticulum will gracefully handle IP links that go up and down,
|
|
and restore connectivity after a failure, once the other end of a TCP interface reappears.
|
|
|
|
.. code::
|
|
|
|
# Here's an example of a TCP Client interface. The
|
|
# target_host can either be an IP address or a hostname.
|
|
|
|
[[TCP Client Interface]]
|
|
type = TCPClientInterface
|
|
interface_enabled = True
|
|
target_host = 127.0.0.1
|
|
target_port = 4242
|
|
|
|
It is also possible to use this interface type to connect via other programs
|
|
or hardware devices that expose a KISS interface on a TCP port, for example
|
|
software-based soundmodems. To do this, use the ``kiss_framing`` option:
|
|
|
|
.. code::
|
|
|
|
# Here's an example of a TCP Client interface that connects
|
|
# to a software TNC soundmodem on a KISS over TCP port.
|
|
|
|
[[TCP KISS Interface]]
|
|
type = TCPClientInterface
|
|
interface_enabled = True
|
|
kiss_framing = True
|
|
target_host = 127.0.0.1
|
|
target_port = 8001
|
|
|
|
**Caution!** Only use the KISS framing option when connecting to external devices
|
|
and programs like soundmodems and similar over TCP. When using the
|
|
``TCPClientInterface`` in conjunction with the ``TCPServerInterface`` you should
|
|
never enable ``kiss_framing``, since this will disable internal reliability and
|
|
recovery mechanisms that greatly improves performance over unreliable and
|
|
intermittent TCP links.
|
|
|
|
**Please Note!** The TCP interfaces support tunneling over I2P, but to do so reliably,
|
|
you must use the i2p_tunneled option:
|
|
|
|
.. code::
|
|
|
|
[[TCP Client over I2P]]
|
|
type = TCPClientInterface
|
|
interface_enabled = yes
|
|
target_host = 127.0.0.1
|
|
target_port = 5001
|
|
i2p_tunneled = yes
|
|
|
|
|
|
.. _interfaces-udp:
|
|
|
|
UDP Interface
|
|
=============
|
|
|
|
A UDP interface can be useful for communicating over IP networks, both
|
|
private and the internet. It can also allow broadcast communication
|
|
over IP networks, so it can provide an easy way to enable connectivity
|
|
with all other peers on a local area network.
|
|
|
|
*Please Note!* Using broadcast UDP traffic has performance implications,
|
|
especially on WiFi. If your goal is simply to enable easy communication
|
|
with all peers in your local Ethernet broadcast domain, the
|
|
:ref:`Auto Interface<interfaces-auto>` performs better, and is even
|
|
easier to use.
|
|
|
|
.. code::
|
|
|
|
# This example enables communication with other
|
|
# local Reticulum peers over UDP.
|
|
|
|
[[UDP Interface]]
|
|
type = UDPInterface
|
|
interface_enabled = True
|
|
|
|
listen_ip = 0.0.0.0
|
|
listen_port = 4242
|
|
forward_ip = 255.255.255.255
|
|
forward_port = 4242
|
|
|
|
# The above configuration will allow communication
|
|
# within the local broadcast domains of all local
|
|
# IP interfaces.
|
|
|
|
# Instead of specifying listen_ip, listen_port,
|
|
# forward_ip and forward_port, you can also bind
|
|
# to a specific network device like below.
|
|
|
|
# device = eth0
|
|
# port = 4242
|
|
|
|
# Assuming the eth0 device has the address
|
|
# 10.55.0.72/24, the above configuration would
|
|
# be equivalent to the following manual setup.
|
|
# Note that we are both listening and forwarding to
|
|
# the broadcast address of the network segments.
|
|
|
|
# listen_ip = 10.55.0.255
|
|
# listen_port = 4242
|
|
# forward_ip = 10.55.0.255
|
|
# forward_port = 4242
|
|
|
|
# You can of course also communicate only with
|
|
# a single IP address
|
|
|
|
# listen_ip = 10.55.0.15
|
|
# listen_port = 4242
|
|
# forward_ip = 10.55.0.16
|
|
# forward_port = 4242
|
|
|
|
|
|
.. _interfaces-rnode:
|
|
|
|
RNode LoRa Interface
|
|
====================
|
|
|
|
To use Reticulum over LoRa, the `RNode <https://unsigned.io/rnode/>`_ interface
|
|
can be used, and offers full control over LoRa parameters.
|
|
|
|
.. code::
|
|
|
|
# Here's an example of how to add a LoRa interface
|
|
# using the RNode LoRa transceiver.
|
|
|
|
[[RNode LoRa Interface]]
|
|
type = RNodeInterface
|
|
|
|
# Enable interface if you want use it!
|
|
interface_enabled = True
|
|
|
|
# Serial port for the device
|
|
port = /dev/ttyUSB0
|
|
|
|
# Set frequency to 867.2 MHz
|
|
frequency = 867200000
|
|
|
|
# Set LoRa bandwidth to 125 KHz
|
|
bandwidth = 125000
|
|
|
|
# Set TX power to 7 dBm (5 mW)
|
|
txpower = 7
|
|
|
|
# Select spreading factor 8. Valid
|
|
# range is 7 through 12, with 7
|
|
# being the fastest and 12 having
|
|
# the longest range.
|
|
spreadingfactor = 8
|
|
|
|
# Select coding rate 5. Valid range
|
|
# is 5 throough 8, with 5 being the
|
|
# fastest, and 8 the longest range.
|
|
codingrate = 5
|
|
|
|
# You can configure the RNode to send
|
|
# out identification on the channel with
|
|
# a set interval by configuring the
|
|
# following two parameters.
|
|
# id_callsign = MYCALL-0
|
|
# id_interval = 600
|
|
|
|
# For certain homebrew RNode interfaces
|
|
# with low amounts of RAM, using packet
|
|
# flow control can be useful. By default
|
|
# it is disabled.
|
|
flow_control = False
|
|
|
|
.. _interfaces-serial:
|
|
|
|
Serial Interface
|
|
================
|
|
|
|
Reticulum can be used over serial ports directly, or over any device with a
|
|
serial port, that will transparently pass data. Useful for communicating
|
|
directly over a wire-pair, or for using devices such as data radios and lasers.
|
|
|
|
.. code::
|
|
|
|
[[Serial Interface]]
|
|
type = SerialInterface
|
|
interface_enabled = True
|
|
|
|
# Serial port for the device
|
|
port = /dev/ttyUSB0
|
|
|
|
# Set the serial baud-rate and other
|
|
# configuration parameters.
|
|
speed = 115200
|
|
databits = 8
|
|
parity = none
|
|
stopbits = 1
|
|
|
|
.. _interfaces-pipe:
|
|
|
|
Pipe Interface
|
|
==============
|
|
|
|
Using this interface, Reticulum can use any program as an interface via `stdin` and
|
|
`stdout`. This can be used to easily create virtual interfaces, or to interface with
|
|
custom hardware or other systems.
|
|
|
|
.. code::
|
|
|
|
[[Pipe Interface]]
|
|
type = PipeInterface
|
|
interface_enabled = True
|
|
|
|
# External command to execute
|
|
command = netcat -l 5757
|
|
|
|
# Optional respawn delay, in seconds
|
|
respawn_delay = 5
|
|
|
|
Reticulum will write all packets to `stdin` of the ``command`` option, and will
|
|
continuously read and scan its `stdout` for Reticulum packets. If ``EOF`` is reached,
|
|
Reticulum will try to respawn the program after waiting for ``respawn_interval`` seconds.
|
|
|
|
.. _interfaces-kiss:
|
|
|
|
KISS Interface
|
|
==============
|
|
|
|
With the KISS interface, you can use Reticulum over a variety of packet
|
|
radio modems and TNCs, including `OpenModem <https://unsigned.io/openmodem/>`_.
|
|
KISS interfaces can also be configured to periodically send out beacons
|
|
for station identification purposes.
|
|
|
|
.. code::
|
|
|
|
[[Packet Radio KISS Interface]]
|
|
type = KISSInterface
|
|
interface_enabled = True
|
|
|
|
# Serial port for the device
|
|
port = /dev/ttyUSB1
|
|
|
|
# Set the serial baud-rate and other
|
|
# configuration parameters.
|
|
speed = 115200
|
|
databits = 8
|
|
parity = none
|
|
stopbits = 1
|
|
|
|
# Set the modem preamble.
|
|
preamble = 150
|
|
|
|
# Set the modem TX tail.
|
|
txtail = 10
|
|
|
|
# Configure CDMA parameters. These
|
|
# settings are reasonable defaults.
|
|
persistence = 200
|
|
slottime = 20
|
|
|
|
# You can configure the interface to send
|
|
# out identification on the channel with
|
|
# a set interval by configuring the
|
|
# following two parameters. The KISS
|
|
# interface will only ID if the set
|
|
# interval has elapsed since it's last
|
|
# actual transmission. The interval is
|
|
# configured in seconds.
|
|
# This option is commented out and not
|
|
# used by default.
|
|
# id_callsign = MYCALL-0
|
|
# id_interval = 600
|
|
|
|
# Whether to use KISS flow-control.
|
|
# This is useful for modems that have
|
|
# a small internal packet buffer, but
|
|
# support packet flow control instead.
|
|
flow_control = false
|
|
|
|
.. _interfaces-ax25:
|
|
|
|
AX.25 KISS Interface
|
|
====================
|
|
|
|
If you're using Reticulum on amateur radio spectrum, you might want to
|
|
use the AX.25 KISS interface. This way, Reticulum will automatically
|
|
encapsulate it's traffic in AX.25 and also identify your stations
|
|
transmissions with your callsign and SSID.
|
|
|
|
Only do this if you really need to! Reticulum doesn't need the AX.25
|
|
layer for anything, and it incurs extra overhead on every packet to
|
|
encapsulate in AX.25.
|
|
|
|
A more efficient way is to use the plain KISS interface with the
|
|
beaconing functionality described above.
|
|
|
|
.. code::
|
|
|
|
[[Packet Radio AX.25 KISS Interface]]
|
|
type = AX25KISSInterface
|
|
|
|
# Set the station callsign and SSID
|
|
callsign = NO1CLL
|
|
ssid = 0
|
|
|
|
# Enable interface if you want use it!
|
|
interface_enabled = True
|
|
|
|
# Serial port for the device
|
|
port = /dev/ttyUSB2
|
|
|
|
# Set the serial baud-rate and other
|
|
# configuration parameters.
|
|
speed = 115200
|
|
databits = 8
|
|
parity = none
|
|
stopbits = 1
|
|
|
|
# Set the modem preamble. A 150ms
|
|
# preamble should be a reasonable
|
|
# default, but may need to be
|
|
# increased for radios with slow-
|
|
# opening squelch and long TX/RX
|
|
# turnaround
|
|
preamble = 150
|
|
|
|
# Set the modem TX tail. In most
|
|
# cases this should be kept as low
|
|
# as possible to not waste airtime.
|
|
txtail = 10
|
|
|
|
# Configure CDMA parameters. These
|
|
# settings are reasonable defaults.
|
|
persistence = 200
|
|
slottime = 20
|
|
|
|
# Whether to use KISS flow-control.
|
|
# This is useful for modems with a
|
|
# small internal packet buffer.
|
|
flow_control = false
|
|
|
|
.. _interfaces-options:
|
|
|
|
Common Interface Options
|
|
========================
|
|
|
|
A number of general configuration options are available on most interfaces.
|
|
These can be used to control various aspects of interface behaviour.
|
|
|
|
|
|
* | The ``enabled`` option tells Reticulum whether or not
|
|
to bring up the interface. Defaults to ``False``. For any
|
|
interface to be brought up, the ``enabled`` option
|
|
must be set to ``True`` or ``Yes``.
|
|
|
|
* | The ``mode`` option allows selecting the high-level behaviour
|
|
of the interface from a number of options.
|
|
|
|
- The default value is ``full``. In this mode, all discovery,
|
|
meshing and transport functionality is available.
|
|
|
|
- In the ``access_point`` (or shorthand ``ap``) mode, the
|
|
interface will operate as a network access point. In this
|
|
mode, announces will not be automatically broadcasted on
|
|
the interface, and paths to destinations on the interface
|
|
will have a much shorter expiry time. This mode is useful
|
|
for creating interfaces that are mostly quiet, unless when
|
|
someone is actually using them. An example of this could
|
|
be a radio interface serving a wide area, where users are
|
|
expected to connect momentarily, use the network, and then
|
|
disappear again.
|
|
|
|
* | The ``outgoing`` option sets whether an interface is allowed
|
|
to transmit. Defaults to ``True``. If set to ``False`` or ``No``
|
|
the interface will only receive data, and never transmit.
|
|
|
|
* | The ``network_name`` option sets the virtual network name for
|
|
the interface. This allows multiple separate network segments
|
|
to exist on the same physical channel or medium.
|
|
|
|
* | The ``passphrase`` option sets an authentication passphrase on
|
|
the interface. This option can be used in conjunction with the
|
|
``network_name`` option, or be used alone.
|
|
|
|
* | The ``ifac_size`` option allows customising the length of the
|
|
Interface Authentication Codes carried by each packet on named
|
|
and/or authenticated network segments. It is set by default to
|
|
a size suitable for the interface in question, but can be set
|
|
to a custom size between 8 and 512 bits by using this option.
|
|
In normal usage, this option should not be changed from the
|
|
default.
|
|
|
|
* | The ``announce_cap`` option lets you configure the maximum
|
|
bandwidth to allocate, at any given time, to propagating
|
|
announces and other network upkeep traffic. It is configured at
|
|
2% by default, and should normally not need to be changed. Can
|
|
be set to any value between ``1`` and ``100``.
|
|
|
|
*If an interface exceeds its announce cap, it will queue announces
|
|
for later transmission. Reticulum will always prioritise propagating
|
|
announces from nearby nodes first. This ensures that the local
|
|
topology is prioritised, and that slow networks are not overwhelmed
|
|
by interconnected fast networks.*
|
|
|
|
*Destinations that are rapidly re-announcing will be down-prioritised
|
|
further. Trying to get "first-in-line" by announce spamming will have
|
|
the exact opposite effect: Getting moved to the back of the queue every
|
|
time a new announce from the excessively announcing destination is received.*
|
|
|
|
*This means that it is always beneficial to select a balanced
|
|
announce rate, and not announce more often than is actually necesarry
|
|
for your application to function.*
|
|
|
|
* | The ``bitrate`` option configures the interface bitrate.
|
|
Reticulum will use interface speeds reported by hardware, or
|
|
try to guess a suitable rate when the hardware doesn't report
|
|
any. In most cases, the automatically found rate should be
|
|
sufficient, but it can be configured by using the ``bitrate``
|
|
option, to set the interface speed in *bits per second*.
|
|
|
|
|
|
.. _interfaces-modes:
|
|
|
|
Interface Modes
|
|
===============
|
|
|
|
The optional ``mode`` setting is available on all interfaces, and allows
|
|
selecting the high-level behaviour of the interface from a number of modes.
|
|
These modes affect how Reticulum selects paths in the network, how announces
|
|
are propagated, how long paths are valid and how paths are discovered.
|
|
|
|
Configuring modes on interfaces is **not** strictly necessary, but can be useful
|
|
when building or connecting to more complex networks. If your Reticulum
|
|
instance is not running a Transport Node, it is rarely useful to configure
|
|
interface modes, and in such cases interfaces should generally be left in
|
|
the default mode.
|
|
|
|
* | The default mode is ``full``. In this mode, all discovery,
|
|
meshing and transport functionality is activated.
|
|
|
|
* | The ``gateway`` mode (or shorthand ``gw``) also has all
|
|
discovery, meshing and transport functionality available,
|
|
but will additionally try to discover unknown paths on
|
|
behalf of other nodes residing on the ``gateway`` interface.
|
|
If Reticulum receives a path request for an unknown
|
|
destination, from a node on a ``gateway`` interface, it
|
|
will try to discover this path via all other active interfaces,
|
|
and forward the discovered path to the requestor if one is
|
|
found.
|
|
|
|
| If you want to allow other nodes to widely resolve paths or connect
|
|
to a network via an interface, it might be useful to put it in this
|
|
mode. By creating a chain of ``gateway`` interfaces, other
|
|
nodes will be able to immediately discover paths to any
|
|
destination along the chain.
|
|
|
|
| *Please note!* It is the interface *facing the clients* that
|
|
must be put into ``gateway`` mode for this to work, not
|
|
the interface facing the wider network (for this, the ``boundary``
|
|
mode can be useful, though).
|
|
|
|
* | In the ``access_point`` (or shorthand ``ap``) mode, the
|
|
interface will operate as a network access point. In this
|
|
mode, announces will not be automatically broadcasted on
|
|
the interface, and paths to destinations on the interface
|
|
will have a much shorter expiry time. In addition, path
|
|
requests from clients on the access point interface will
|
|
be handled in the same way as the ``gateway`` interface.
|
|
|
|
| This mode is useful for creating interfaces that remain
|
|
quiet, until someone actually starts using them. An example
|
|
of this could be a radio interface serving a wide area,
|
|
where users are expected to connect momentarily, use the
|
|
network, and then disappear again.
|
|
|
|
* | The ``roaming`` mode should be used on interfaces that are
|
|
roaming (physically mobile), seen from the perspective of
|
|
other nodes in the network. As an example, if a vehicle is
|
|
equipped with an external LoRa interface, and an internal,
|
|
WiFi-based interface, that serves devices that are moving
|
|
*with* the vehicle, the external LoRa interface should be
|
|
configured as ``roaming``, and the internal interface can
|
|
be left in the default mode. With transport enabled, such
|
|
a setup will allow all internal devices to reach each other,
|
|
and all other devices that are available on the LoRa side
|
|
of the network, when they are in range. Devices on the LoRa
|
|
side of the network will also be able to reach devices
|
|
internal to the vehicle, when it is in range. Paths via
|
|
``roaming`` interfaces also expire faster.
|
|
|
|
* | The purpose of the ``boundary`` mode is to specify interfaces
|
|
that establish connectivity with network segments that are
|
|
significantly different than the one this node exists on.
|
|
As an example, if a Reticulum instance is part of a LoRa-based
|
|
network, but also has a high-speed connection to a
|
|
public Transport Node available on the Internet, the interface
|
|
connecting over the Internet should be set to ``boundary`` mode.
|
|
|
|
For a table describing the impact of all modes on announce propagation,
|
|
please see the :ref:`Announce Propagation Rules<understanding-announcepropagation>` section.
|
|
|
|
.. _interfaces-announcerates:
|
|
|
|
Announce Rate Control
|
|
=====================
|
|
|
|
The built-in announce control mechanisms and the default ``announce_cap``
|
|
option described above are sufficient most of the time, but in some cases, especially on fast
|
|
interfaces, it may be useful to control the target announce rate. Using the
|
|
``announce_rate_target``, ``announce_rate_grace`` and ``announce_rate_penalty``
|
|
options, this can be done on a per-interface basis, and moderates the *rate at
|
|
which received announces are re-broadcasted to other interfaces*.
|
|
|
|
* | The ``announce_rate_target`` option sets the minimum amount of time,
|
|
in seconds, that should pass between received announces, for any one
|
|
destination. As an example, setting this value to ``3600`` means that
|
|
announces *received* on this interface will only be re-transmitted and
|
|
propagated to other interfaces once every hour, no matter how often they
|
|
are received.
|
|
|
|
* | The optional ``announce_rate_grace`` defines the number of times a destination
|
|
can violate the announce rate before the target rate is enforced.
|
|
|
|
* | The optional ``announce_rate_penalty`` configures an extra amount of
|
|
time that is added to the normal rate target. As an example, if a penalty
|
|
of ``7200`` seconds is defined, once the rate target is enforced, the
|
|
destination in question will only have its announces propagated every
|
|
3 hours, until it lowers its actual announce rate to within the target.
|
|
|
|
These mechanisms, in conjunction with the ``annouce_cap`` mechanisms mentioned
|
|
above means that it is essential to select a balanced announce strategy for
|
|
your destinations. The more balanced you can make this decision, the easier
|
|
it will be for your destinations to make it into slower networks that many hops
|
|
away. Or you can prioritise only reaching high-capacity networks with more frequent
|
|
announces.
|
|
|
|
Current statistics and information about announce rates can be viewed using the
|
|
``rnpath -r`` command.
|
|
|
|
It is important to note that there is no one right or wrong way to set up announce
|
|
rates. Slower networks will naturally tend towards using less frequent announces to
|
|
conserve bandwidth, while very fast networks can support applications that
|
|
need very frequent announces. Reticulum implements these mechanisms to ensure
|
|
that a large span of network types can seamlessly *co-exist* and interconnect.
|
|
|