Added RNodeMultiInterface to documentation

This commit is contained in:
Mark Qvist 2024-08-28 18:47:33 +02:00
parent 4aa60243a7
commit f1d6cda337
11 changed files with 360 additions and 11 deletions

View File

@ -406,6 +406,121 @@ can be used, and offers full control over LoRa parameters.
# airtime_limit_short = 33
.. _interfaces-rnode-multi:
RNode Multi Interface
=====================
For RNodes that support multiple LoRa transceivers, the RNode
Multi interface can be used to configure sub-interfaces individually.
.. code::
# Here's an example of how to add an RNode Multi interface
# using the RNode LoRa transceiver.
[[RNode Multi Interface]]
type = RNodeMultiInterface
# Enable interface if you want to use it!
interface_enabled = True
# Serial port for the device
port = /dev/ttyACM0
# You can configure the RNode to send
# out identification on the channel with
# a set interval by configuring the
# following two parameters.
# id_callsign = MYCALL-0
# id_interval = 600
# A subinterface
[[[HIGHDATARATE]]]
# Subinterfaces can be enabled and disabled in of themselves
interface_enabled = True
# Set frequency to 2.4GHz
frequency = 2400000000
# Set LoRa bandwidth to 1625 KHz
bandwidth = 1625000
# Set TX power to 0 dBm (0.12 mW)
txpower = 0
# The virtual port, only the manufacturer
# or the person who wrote the board config
# can tell you what it will be for which
# physical hardware interface
vport = 1
# Select spreading factor 5. Valid
# range is 5 through 12, with 5
# being the fastest and 12 having
# the longest range.
spreadingfactor = 5
# Select coding rate 5. Valid range
# is 5 throough 8, with 5 being the
# fastest, and 8 the longest range.
codingrate = 5
# It is possible to limit the airtime
# utilisation of an RNode by using the
# following two configuration options.
# The short-term limit is applied in a
# window of approximately 15 seconds,
# and the long-term limit is enforced
# over a rolling 60 minute window. Both
# options are specified in percent.
# airtime_limit_long = 100
# airtime_limit_short = 100
[[[LOWDATARATE]]]
# Subinterfaces can be enabled and disabled in of themselves
interface_enabled = True
# Set frequency to 865.6 MHz
frequency = 865600000
# The virtual port, only the manufacturer
# or the person who wrote the board config
# can tell you what it will be for which
# physical hardware interface
vport = 0
# Set LoRa bandwidth to 125 KHz
bandwidth = 125000
# Set TX power to 0 dBm (0.12 mW)
txpower = 0
# Select spreading factor 7. Valid
# range is 5 through 12, with 5
# being the fastest and 12 having
# the longest range.
spreadingfactor = 7
# Select coding rate 5. Valid range
# is 5 throough 8, with 5 being the
# fastest, and 8 the longest range.
codingrate = 5
# It is possible to limit the airtime
# utilisation of an RNode by using the
# following two configuration options.
# The short-term limit is applied in a
# window of approximately 15 seconds,
# and the long-term limit is enforced
# over a rolling 60 minute window. Both
# options are specified in percent.
# airtime_limit_long = 100
# airtime_limit_short = 100
.. _interfaces-serial:
Serial Interface

View File

@ -60,7 +60,7 @@ with Reticulum:
* | Reticulum is designed to work reliably in open, trustless environments. This
means you can use it to create open-access networks, where participants can
join and leave in an free and unorganised manner. This property allows an
join and leave in a free and unorganised manner. This property allows an
entirely new, and so far, mostly unexplored class of networked applications,
where networks, and the information flow within them can form and dissolve
organically.

View File

@ -106,17 +106,17 @@ body[data-theme="dark"] .highlight .cp { color: #ff3a3a; font-weight: bold } /*
body[data-theme="dark"] .highlight .cpf { color: #ababab; font-style: italic } /* Comment.PreprocFile */
body[data-theme="dark"] .highlight .c1 { color: #ababab; font-style: italic } /* Comment.Single */
body[data-theme="dark"] .highlight .cs { color: #e50808; font-weight: bold; background-color: #520000 } /* Comment.Special */
body[data-theme="dark"] .highlight .gd { color: #d22323 } /* Generic.Deleted */
body[data-theme="dark"] .highlight .gd { color: #ff3a3a } /* Generic.Deleted */
body[data-theme="dark"] .highlight .ge { color: #d0d0d0; font-style: italic } /* Generic.Emph */
body[data-theme="dark"] .highlight .ges { color: #d0d0d0; font-weight: bold; font-style: italic } /* Generic.EmphStrong */
body[data-theme="dark"] .highlight .gr { color: #d22323 } /* Generic.Error */
body[data-theme="dark"] .highlight .gr { color: #ff3a3a } /* Generic.Error */
body[data-theme="dark"] .highlight .gh { color: #ffffff; font-weight: bold } /* Generic.Heading */
body[data-theme="dark"] .highlight .gi { color: #589819 } /* Generic.Inserted */
body[data-theme="dark"] .highlight .go { color: #cccccc } /* Generic.Output */
body[data-theme="dark"] .highlight .gp { color: #aaaaaa } /* Generic.Prompt */
body[data-theme="dark"] .highlight .gs { color: #d0d0d0; font-weight: bold } /* Generic.Strong */
body[data-theme="dark"] .highlight .gu { color: #ffffff; text-decoration: underline } /* Generic.Subheading */
body[data-theme="dark"] .highlight .gt { color: #d22323 } /* Generic.Traceback */
body[data-theme="dark"] .highlight .gt { color: #ff3a3a } /* Generic.Traceback */
body[data-theme="dark"] .highlight .kc { color: #6ebf26; font-weight: bold } /* Keyword.Constant */
body[data-theme="dark"] .highlight .kd { color: #6ebf26; font-weight: bold } /* Keyword.Declaration */
body[data-theme="dark"] .highlight .kn { color: #6ebf26; font-weight: bold } /* Keyword.Namespace */
@ -192,17 +192,17 @@ body:not([data-theme="light"]) .highlight .cp { color: #ff3a3a; font-weight: bol
body:not([data-theme="light"]) .highlight .cpf { color: #ababab; font-style: italic } /* Comment.PreprocFile */
body:not([data-theme="light"]) .highlight .c1 { color: #ababab; font-style: italic } /* Comment.Single */
body:not([data-theme="light"]) .highlight .cs { color: #e50808; font-weight: bold; background-color: #520000 } /* Comment.Special */
body:not([data-theme="light"]) .highlight .gd { color: #d22323 } /* Generic.Deleted */
body:not([data-theme="light"]) .highlight .gd { color: #ff3a3a } /* Generic.Deleted */
body:not([data-theme="light"]) .highlight .ge { color: #d0d0d0; font-style: italic } /* Generic.Emph */
body:not([data-theme="light"]) .highlight .ges { color: #d0d0d0; font-weight: bold; font-style: italic } /* Generic.EmphStrong */
body:not([data-theme="light"]) .highlight .gr { color: #d22323 } /* Generic.Error */
body:not([data-theme="light"]) .highlight .gr { color: #ff3a3a } /* Generic.Error */
body:not([data-theme="light"]) .highlight .gh { color: #ffffff; font-weight: bold } /* Generic.Heading */
body:not([data-theme="light"]) .highlight .gi { color: #589819 } /* Generic.Inserted */
body:not([data-theme="light"]) .highlight .go { color: #cccccc } /* Generic.Output */
body:not([data-theme="light"]) .highlight .gp { color: #aaaaaa } /* Generic.Prompt */
body:not([data-theme="light"]) .highlight .gs { color: #d0d0d0; font-weight: bold } /* Generic.Strong */
body:not([data-theme="light"]) .highlight .gu { color: #ffffff; text-decoration: underline } /* Generic.Subheading */
body:not([data-theme="light"]) .highlight .gt { color: #d22323 } /* Generic.Traceback */
body:not([data-theme="light"]) .highlight .gt { color: #ff3a3a } /* Generic.Traceback */
body:not([data-theme="light"]) .highlight .kc { color: #6ebf26; font-weight: bold } /* Keyword.Constant */
body:not([data-theme="light"]) .highlight .kd { color: #6ebf26; font-weight: bold } /* Keyword.Declaration */
body:not([data-theme="light"]) .highlight .kn { color: #6ebf26; font-weight: bold } /* Keyword.Namespace */

View File

@ -1072,7 +1072,7 @@ destination, and passing traffic back and forth over the link.</p>
<span class="s2">&quot; running, waiting for a connection.&quot;</span>
<span class="p">)</span>
<span class="n">RNS</span><span class="o">.</span><span class="n">log</span><span class="p">(</span><span class="s2">&quot;Hit enter to manually send an announce (Ctrl-C to quit)&quot;</span><span class="p">)</span>
<span class="n">RNS</span><span class="o">.</span><span class="n">log</span><span class="p">(</span><span class="s2">&quot;Hit enter to manually send an announce (Ctrl-C or </span><span class="se">\&quot;</span><span class="s2">quit</span><span class="se">\&quot;</span><span class="s2"> to quit)&quot;</span><span class="p">)</span>
<span class="c1"># We enter a loop that runs until the users exits.</span>
<span class="c1"># If the user hits enter, we will announce our server</span>
@ -1082,6 +1082,12 @@ destination, and passing traffic back and forth over the link.</p>
<span class="n">entered</span> <span class="o">=</span> <span class="nb">input</span><span class="p">()</span>
<span class="n">destination</span><span class="o">.</span><span class="n">announce</span><span class="p">()</span>
<span class="n">RNS</span><span class="o">.</span><span class="n">log</span><span class="p">(</span><span class="s2">&quot;Sent announce from &quot;</span><span class="o">+</span><span class="n">RNS</span><span class="o">.</span><span class="n">prettyhexrep</span><span class="p">(</span><span class="n">destination</span><span class="o">.</span><span class="n">hash</span><span class="p">))</span>
<span class="k">if</span> <span class="n">entered</span> <span class="o">==</span> <span class="s2">&quot;quit&quot;</span><span class="p">:</span>
<span class="k">if</span> <span class="n">latest_client_link</span><span class="p">:</span>
<span class="n">latest_client_link</span><span class="o">.</span><span class="n">teardown</span><span class="p">()</span>
<span class="k">break</span>
<span class="nb">print</span><span class="p">(</span><span class="s2">&quot;&quot;</span><span class="p">)</span>
<span class="n">exit</span><span class="p">()</span>
<span class="c1"># When a client establishes a link to our server</span>
<span class="c1"># destination, this function will be called with</span>

View File

@ -409,7 +409,7 @@ by adding one of the following interfaces to your <code class="docutils literal
<span class="p">[[</span><span class="n">RNS</span> <span class="n">Testnet</span> <span class="n">BetweenTheBorders</span><span class="p">]]</span>
<span class="nb">type</span> <span class="o">=</span> <span class="n">TCPClientInterface</span>
<span class="n">enabled</span> <span class="o">=</span> <span class="n">yes</span>
<span class="n">target_host</span> <span class="o">=</span> <span class="n">betweentheborders</span><span class="o">.</span><span class="n">com</span>
<span class="n">target_host</span> <span class="o">=</span> <span class="n">reticulum</span><span class="o">.</span><span class="n">betweentheborders</span><span class="o">.</span><span class="n">com</span>
<span class="n">target_port</span> <span class="o">=</span> <span class="mi">4242</span>
<span class="c1"># Interface to Testnet I2P Hub</span>

View File

@ -338,6 +338,7 @@ to participate in the development of Reticulum itself.</p>
<li class="toctree-l2"><a class="reference internal" href="interfaces.html#tcp-client-interface">TCP Client Interface</a></li>
<li class="toctree-l2"><a class="reference internal" href="interfaces.html#udp-interface">UDP Interface</a></li>
<li class="toctree-l2"><a class="reference internal" href="interfaces.html#rnode-lora-interface">RNode LoRa Interface</a></li>
<li class="toctree-l2"><a class="reference internal" href="interfaces.html#rnode-multi-interface">RNode Multi Interface</a></li>
<li class="toctree-l2"><a class="reference internal" href="interfaces.html#serial-interface">Serial Interface</a></li>
<li class="toctree-l2"><a class="reference internal" href="interfaces.html#pipe-interface">Pipe Interface</a></li>
<li class="toctree-l2"><a class="reference internal" href="interfaces.html#kiss-interface">KISS Interface</a></li>

View File

@ -569,6 +569,117 @@ can be used, and offers full control over LoRa parameters.</p>
</pre></div>
</div>
</section>
<section id="rnode-multi-interface">
<span id="interfaces-rnode-multi"></span><h2>RNode Multi Interface<a class="headerlink" href="#rnode-multi-interface" title="Permalink to this heading">#</a></h2>
<p>For RNodes that support multiple LoRa transceivers, the RNode
Multi interface can be used to configure sub-interfaces individually.</p>
<div class="highlight-default notranslate"><div class="highlight"><pre><span></span><span class="c1"># Here&#39;s an example of how to add an RNode Multi interface</span>
<span class="c1"># using the RNode LoRa transceiver.</span>
<span class="p">[[</span><span class="n">RNode</span> <span class="n">Multi</span> <span class="n">Interface</span><span class="p">]]</span>
<span class="nb">type</span> <span class="o">=</span> <span class="n">RNodeMultiInterface</span>
<span class="c1"># Enable interface if you want to use it!</span>
<span class="n">interface_enabled</span> <span class="o">=</span> <span class="kc">True</span>
<span class="c1"># Serial port for the device</span>
<span class="n">port</span> <span class="o">=</span> <span class="o">/</span><span class="n">dev</span><span class="o">/</span><span class="n">ttyACM0</span>
<span class="c1"># You can configure the RNode to send</span>
<span class="c1"># out identification on the channel with</span>
<span class="c1"># a set interval by configuring the</span>
<span class="c1"># following two parameters.</span>
<span class="c1"># id_callsign = MYCALL-0</span>
<span class="c1"># id_interval = 600</span>
<span class="c1"># A subinterface</span>
<span class="p">[[[</span><span class="n">HIGHDATARATE</span><span class="p">]]]</span>
<span class="c1"># Subinterfaces can be enabled and disabled in of themselves</span>
<span class="n">interface_enabled</span> <span class="o">=</span> <span class="kc">True</span>
<span class="c1"># Set frequency to 2.4GHz</span>
<span class="n">frequency</span> <span class="o">=</span> <span class="mi">2400000000</span>
<span class="c1"># Set LoRa bandwidth to 1625 KHz</span>
<span class="n">bandwidth</span> <span class="o">=</span> <span class="mi">1625000</span>
<span class="c1"># Set TX power to 0 dBm (0.12 mW)</span>
<span class="n">txpower</span> <span class="o">=</span> <span class="mi">0</span>
<span class="c1"># The virtual port, only the manufacturer</span>
<span class="c1"># or the person who wrote the board config</span>
<span class="c1"># can tell you what it will be for which</span>
<span class="c1"># physical hardware interface</span>
<span class="n">vport</span> <span class="o">=</span> <span class="mi">1</span>
<span class="c1"># Select spreading factor 5. Valid</span>
<span class="c1"># range is 5 through 12, with 5</span>
<span class="c1"># being the fastest and 12 having</span>
<span class="c1"># the longest range.</span>
<span class="n">spreadingfactor</span> <span class="o">=</span> <span class="mi">5</span>
<span class="c1"># Select coding rate 5. Valid range</span>
<span class="c1"># is 5 throough 8, with 5 being the</span>
<span class="c1"># fastest, and 8 the longest range.</span>
<span class="n">codingrate</span> <span class="o">=</span> <span class="mi">5</span>
<span class="c1"># It is possible to limit the airtime</span>
<span class="c1"># utilisation of an RNode by using the</span>
<span class="c1"># following two configuration options.</span>
<span class="c1"># The short-term limit is applied in a</span>
<span class="c1"># window of approximately 15 seconds,</span>
<span class="c1"># and the long-term limit is enforced</span>
<span class="c1"># over a rolling 60 minute window. Both</span>
<span class="c1"># options are specified in percent.</span>
<span class="c1"># airtime_limit_long = 100</span>
<span class="c1"># airtime_limit_short = 100</span>
<span class="p">[[[</span><span class="n">LOWDATARATE</span><span class="p">]]]</span>
<span class="c1"># Subinterfaces can be enabled and disabled in of themselves</span>
<span class="n">interface_enabled</span> <span class="o">=</span> <span class="kc">True</span>
<span class="c1"># Set frequency to 865.6 MHz</span>
<span class="n">frequency</span> <span class="o">=</span> <span class="mi">865600000</span>
<span class="c1"># The virtual port, only the manufacturer</span>
<span class="c1"># or the person who wrote the board config</span>
<span class="c1"># can tell you what it will be for which</span>
<span class="c1"># physical hardware interface</span>
<span class="n">vport</span> <span class="o">=</span> <span class="mi">0</span>
<span class="c1"># Set LoRa bandwidth to 125 KHz</span>
<span class="n">bandwidth</span> <span class="o">=</span> <span class="mi">125000</span>
<span class="c1"># Set TX power to 0 dBm (0.12 mW)</span>
<span class="n">txpower</span> <span class="o">=</span> <span class="mi">0</span>
<span class="c1"># Select spreading factor 7. Valid</span>
<span class="c1"># range is 5 through 12, with 5</span>
<span class="c1"># being the fastest and 12 having</span>
<span class="c1"># the longest range.</span>
<span class="n">spreadingfactor</span> <span class="o">=</span> <span class="mi">7</span>
<span class="c1"># Select coding rate 5. Valid range</span>
<span class="c1"># is 5 throough 8, with 5 being the</span>
<span class="c1"># fastest, and 8 the longest range.</span>
<span class="n">codingrate</span> <span class="o">=</span> <span class="mi">5</span>
<span class="c1"># It is possible to limit the airtime</span>
<span class="c1"># utilisation of an RNode by using the</span>
<span class="c1"># following two configuration options.</span>
<span class="c1"># The short-term limit is applied in a</span>
<span class="c1"># window of approximately 15 seconds,</span>
<span class="c1"># and the long-term limit is enforced</span>
<span class="c1"># over a rolling 60 minute window. Both</span>
<span class="c1"># options are specified in percent.</span>
<span class="c1"># airtime_limit_long = 100</span>
<span class="c1"># airtime_limit_short = 100</span>
</pre></div>
</div>
</section>
<section id="serial-interface">
<span id="interfaces-serial"></span><h2>Serial Interface<a class="headerlink" href="#serial-interface" title="Permalink to this heading">#</a></h2>
<p>Reticulum can be used over serial ports directly, or over any device with a
@ -1104,6 +1215,7 @@ to <code class="docutils literal notranslate"><span class="pre">30</span></code>
<li><a class="reference internal" href="#tcp-client-interface">TCP Client Interface</a></li>
<li><a class="reference internal" href="#udp-interface">UDP Interface</a></li>
<li><a class="reference internal" href="#rnode-lora-interface">RNode LoRa Interface</a></li>
<li><a class="reference internal" href="#rnode-multi-interface">RNode Multi Interface</a></li>
<li><a class="reference internal" href="#serial-interface">Serial Interface</a></li>
<li><a class="reference internal" href="#pipe-interface">Pipe Interface</a></li>
<li><a class="reference internal" href="#kiss-interface">KISS Interface</a></li>

View File

@ -294,7 +294,7 @@ than that.</em></p>
<li><div class="line-block">
<div class="line">Reticulum is designed to work reliably in open, trustless environments. This
means you can use it to create open-access networks, where participants can
join and leave in an free and unorganised manner. This property allows an
join and leave in a free and unorganised manner. This property allows an
entirely new, and so far, mostly unexplored class of networked applications,
where networks, and the information flow within them can form and dissolve
organically.</div>

Binary file not shown.

File diff suppressed because one or more lines are too long

View File

@ -406,6 +406,121 @@ can be used, and offers full control over LoRa parameters.
# airtime_limit_short = 33
.. _interfaces-rnode-multi:
RNode Multi Interface
=====================
For RNodes that support multiple LoRa transceivers, the RNode
Multi interface can be used to configure sub-interfaces individually.
.. code::
# Here's an example of how to add an RNode Multi interface
# using the RNode LoRa transceiver.
[[RNode Multi Interface]]
type = RNodeMultiInterface
# Enable interface if you want to use it!
interface_enabled = True
# Serial port for the device
port = /dev/ttyACM0
# You can configure the RNode to send
# out identification on the channel with
# a set interval by configuring the
# following two parameters.
# id_callsign = MYCALL-0
# id_interval = 600
# A subinterface
[[[HIGHDATARATE]]]
# Subinterfaces can be enabled and disabled in of themselves
interface_enabled = True
# Set frequency to 2.4GHz
frequency = 2400000000
# Set LoRa bandwidth to 1625 KHz
bandwidth = 1625000
# Set TX power to 0 dBm (0.12 mW)
txpower = 0
# The virtual port, only the manufacturer
# or the person who wrote the board config
# can tell you what it will be for which
# physical hardware interface
vport = 1
# Select spreading factor 5. Valid
# range is 5 through 12, with 5
# being the fastest and 12 having
# the longest range.
spreadingfactor = 5
# Select coding rate 5. Valid range
# is 5 throough 8, with 5 being the
# fastest, and 8 the longest range.
codingrate = 5
# It is possible to limit the airtime
# utilisation of an RNode by using the
# following two configuration options.
# The short-term limit is applied in a
# window of approximately 15 seconds,
# and the long-term limit is enforced
# over a rolling 60 minute window. Both
# options are specified in percent.
# airtime_limit_long = 100
# airtime_limit_short = 100
[[[LOWDATARATE]]]
# Subinterfaces can be enabled and disabled in of themselves
interface_enabled = True
# Set frequency to 865.6 MHz
frequency = 865600000
# The virtual port, only the manufacturer
# or the person who wrote the board config
# can tell you what it will be for which
# physical hardware interface
vport = 0
# Set LoRa bandwidth to 125 KHz
bandwidth = 125000
# Set TX power to 0 dBm (0.12 mW)
txpower = 0
# Select spreading factor 7. Valid
# range is 5 through 12, with 5
# being the fastest and 12 having
# the longest range.
spreadingfactor = 7
# Select coding rate 5. Valid range
# is 5 throough 8, with 5 being the
# fastest, and 8 the longest range.
codingrate = 5
# It is possible to limit the airtime
# utilisation of an RNode by using the
# following two configuration options.
# The short-term limit is applied in a
# window of approximately 15 seconds,
# and the long-term limit is enforced
# over a rolling 60 minute window. Both
# options are specified in percent.
# airtime_limit_long = 100
# airtime_limit_short = 100
.. _interfaces-serial:
Serial Interface