mirror of
https://github.com/markqvist/Reticulum.git
synced 2024-11-22 21:50:18 +00:00
Restructured default config and added config example to rnsd
This commit is contained in:
Mark Qvist
parent
87a274d177
commit
15d027e11e
250
RNS/Reticulum.py
250
RNS/Reticulum.py
@ -754,6 +754,11 @@ __default_rns_config__ = '''# This is the default Reticulum config file.
|
||||
# You should probably edit it to include any additional,
|
||||
# interfaces and settings you might need.
|
||||
|
||||
# Only the most basic options are included in this default
|
||||
# configuration. To see a more verbose, and much longer,
|
||||
# configuration example, you can run the command:
|
||||
# rnsd --exampleconfig
|
||||
|
||||
[reticulum]
|
||||
|
||||
# If you enable Transport, your system will route traffic
|
||||
@ -830,249 +835,4 @@ loglevel = 4
|
||||
type = AutoInterface
|
||||
interface_enabled = True
|
||||
|
||||
|
||||
# The following example enables communication with other
|
||||
# local Reticulum peers using UDP broadcasts.
|
||||
|
||||
[[UDP Interface]]
|
||||
type = UDPInterface
|
||||
interface_enabled = False
|
||||
listen_ip = 0.0.0.0
|
||||
listen_port = 4242
|
||||
forward_ip = 255.255.255.255
|
||||
forward_port = 4242
|
||||
|
||||
# The above configuration will allow communication
|
||||
# within the local broadcast domains of all local
|
||||
# IP interfaces.
|
||||
|
||||
# Instead of specifying listen_ip, listen_port,
|
||||
# forward_ip and forward_port, you can also bind
|
||||
# to a specific network device like below.
|
||||
|
||||
# device = eth0
|
||||
# port = 4242
|
||||
|
||||
# Assuming the eth0 device has the address
|
||||
# 10.55.0.72/24, the above configuration would
|
||||
# be equivalent to the following manual setup.
|
||||
# Note that we are both listening and forwarding to
|
||||
# the broadcast address of the network segments.
|
||||
|
||||
# listen_ip = 10.55.0.255
|
||||
# listen_port = 4242
|
||||
# forward_ip = 10.55.0.255
|
||||
# forward_port = 4242
|
||||
|
||||
# You can of course also communicate only with
|
||||
# a single IP address
|
||||
|
||||
# listen_ip = 10.55.0.15
|
||||
# listen_port = 4242
|
||||
# forward_ip = 10.55.0.16
|
||||
# forward_port = 4242
|
||||
|
||||
|
||||
# This example demonstrates a TCP server interface.
|
||||
# It will listen for incoming connections on the
|
||||
# specified IP address and port number.
|
||||
|
||||
[[TCP Server Interface]]
|
||||
type = TCPServerInterface
|
||||
interface_enabled = False
|
||||
|
||||
# This configuration will listen on all IP
|
||||
# interfaces on port 4242
|
||||
|
||||
listen_ip = 0.0.0.0
|
||||
listen_port = 4242
|
||||
|
||||
# Alternatively you can bind to a specific IP
|
||||
|
||||
# listen_ip = 10.0.0.88
|
||||
# listen_port = 4242
|
||||
|
||||
# Or a specific network device
|
||||
|
||||
# device = eth0
|
||||
# port = 4242
|
||||
|
||||
|
||||
# To connect to a TCP server interface, you would
|
||||
# naturally use the TCP client interface. Here's
|
||||
# an example. The target_host can either be an IP
|
||||
# address or a hostname
|
||||
|
||||
[[TCP Client Interface]]
|
||||
type = TCPClientInterface
|
||||
interface_enabled = False
|
||||
target_host = 127.0.0.1
|
||||
target_port = 4242
|
||||
|
||||
|
||||
# Here's an example of how to add a LoRa interface
|
||||
# using the RNode LoRa transceiver.
|
||||
|
||||
[[RNode LoRa Interface]]
|
||||
type = RNodeInterface
|
||||
|
||||
# Enable interface if you want use it!
|
||||
interface_enabled = False
|
||||
|
||||
# Serial port for the device
|
||||
port = /dev/ttyUSB0
|
||||
|
||||
# Set frequency to 867.2 MHz
|
||||
frequency = 867200000
|
||||
|
||||
# Set LoRa bandwidth to 125 KHz
|
||||
bandwidth = 125000
|
||||
|
||||
# Set TX power to 7 dBm (5 mW)
|
||||
txpower = 7
|
||||
|
||||
# Select spreading factor 8. Valid
|
||||
# range is 7 through 12, with 7
|
||||
# being the fastest and 12 having
|
||||
# the longest range.
|
||||
spreadingfactor = 8
|
||||
|
||||
# Select coding rate 5. Valid range
|
||||
# is 5 throough 8, with 5 being the
|
||||
# fastest, and 8 the longest range.
|
||||
codingrate = 5
|
||||
|
||||
# You can configure the RNode to send
|
||||
# out identification on the channel with
|
||||
# a set interval by configuring the
|
||||
# following two parameters. The trans-
|
||||
# ceiver will only ID if the set
|
||||
# interval has elapsed since it's last
|
||||
# actual transmission. The interval is
|
||||
# configured in seconds.
|
||||
# This option is commented out and not
|
||||
# used by default.
|
||||
# id_callsign = MYCALL-0
|
||||
# id_interval = 600
|
||||
|
||||
# For certain homebrew RNode interfaces
|
||||
# with low amounts of RAM, using packet
|
||||
# flow control can be useful. By default
|
||||
# it is disabled.
|
||||
flow_control = False
|
||||
|
||||
|
||||
# An example KISS modem interface. Useful for running
|
||||
# Reticulum over packet radio hardware.
|
||||
|
||||
[[Packet Radio KISS Interface]]
|
||||
type = KISSInterface
|
||||
|
||||
# Enable interface if you want use it!
|
||||
interface_enabled = False
|
||||
|
||||
# Serial port for the device
|
||||
port = /dev/ttyUSB1
|
||||
|
||||
# Set the serial baud-rate and other
|
||||
# configuration parameters.
|
||||
speed = 115200
|
||||
databits = 8
|
||||
parity = none
|
||||
stopbits = 1
|
||||
|
||||
# Set the modem preamble. A 150ms
|
||||
# preamble should be a reasonable
|
||||
# default, but may need to be
|
||||
# increased for radios with slow-
|
||||
# opening squelch and long TX/RX
|
||||
# turnaround
|
||||
preamble = 150
|
||||
|
||||
# Set the modem TX tail. In most
|
||||
# cases this should be kept as low
|
||||
# as possible to not waste airtime.
|
||||
txtail = 10
|
||||
|
||||
# Configure CDMA parameters. These
|
||||
# settings are reasonable defaults.
|
||||
persistence = 200
|
||||
slottime = 20
|
||||
|
||||
# You can configure the interface to send
|
||||
# out identification on the channel with
|
||||
# a set interval by configuring the
|
||||
# following two parameters. The KISS
|
||||
# interface will only ID if the set
|
||||
# interval has elapsed since it's last
|
||||
# actual transmission. The interval is
|
||||
# configured in seconds.
|
||||
# This option is commented out and not
|
||||
# used by default.
|
||||
# id_callsign = MYCALL-0
|
||||
# id_interval = 600
|
||||
|
||||
# Whether to use KISS flow-control.
|
||||
# This is useful for modems that have
|
||||
# a small internal packet buffer, but
|
||||
# support packet flow control instead.
|
||||
flow_control = false
|
||||
|
||||
|
||||
# If you're using Reticulum on amateur radio spectrum,
|
||||
# you might want to use the AX.25 KISS interface. This
|
||||
# way, Reticulum will automatically encapsulate it's
|
||||
# traffic in AX.25 and also identify your stations
|
||||
# transmissions with your callsign and SSID.
|
||||
#
|
||||
# Only do this if you really need to! Reticulum doesn't
|
||||
# need the AX.25 layer for anything, and it incurs extra
|
||||
# overhead on every packet to encapsulate in AX.25.
|
||||
#
|
||||
# A more efficient way is to use the plain KISS interface
|
||||
# with the beaconing functionality described above.
|
||||
|
||||
[[Packet Radio AX.25 KISS Interface]]
|
||||
type = AX25KISSInterface
|
||||
|
||||
# Set the station callsign and SSID
|
||||
callsign = NO1CLL
|
||||
ssid = 0
|
||||
|
||||
# Enable interface if you want use it!
|
||||
interface_enabled = False
|
||||
|
||||
# Serial port for the device
|
||||
port = /dev/ttyUSB2
|
||||
|
||||
# Set the serial baud-rate and other
|
||||
# configuration parameters.
|
||||
speed = 115200
|
||||
databits = 8
|
||||
parity = none
|
||||
stopbits = 1
|
||||
|
||||
# Whether to use KISS flow-control.
|
||||
# This is useful for modems with a
|
||||
# small internal packet buffer.
|
||||
flow_control = false
|
||||
|
||||
# Set the modem preamble. A 150ms
|
||||
# preamble should be a reasonable
|
||||
# default, but may need to be
|
||||
# increased for radios with slow-
|
||||
# opening squelch and long TX/RX
|
||||
# turnaround
|
||||
preamble = 150
|
||||
|
||||
# Set the modem TX tail. In most
|
||||
# cases this should be kept as low
|
||||
# as possible to not waste airtime.
|
||||
txtail = 10
|
||||
|
||||
# Configure CDMA parameters. These
|
||||
# settings are reasonable defaults.
|
||||
persistence = 200
|
||||
slottime = 20
|
||||
|
||||
'''.splitlines()
|
||||
|
||||
@ -27,10 +27,15 @@ def main():
|
||||
parser.add_argument('-v', '--verbose', action='count', default=0)
|
||||
parser.add_argument('-q', '--quiet', action='count', default=0)
|
||||
parser.add_argument('-s', '--service', action='store_true', default=False, help="rnsd is running as a service and should log to file")
|
||||
parser.add_argument("--exampleconfig", action='store_true', default=False, help="print verbose configuration example to stdout and exit")
|
||||
parser.add_argument("--version", action="version", version="rnsd {version}".format(version=__version__))
|
||||
|
||||
args = parser.parse_args()
|
||||
|
||||
if args.exampleconfig:
|
||||
print(__example_rns_config__)
|
||||
exit()
|
||||
|
||||
if args.config:
|
||||
configarg = args.config
|
||||
else:
|
||||
@ -42,5 +47,344 @@ def main():
|
||||
print("")
|
||||
exit()
|
||||
|
||||
__example_rns_config__ = '''# This is an example Reticulum config file.
|
||||
# You should probably edit it to include any additional,
|
||||
# interfaces and settings you might need.
|
||||
|
||||
[reticulum]
|
||||
|
||||
# If you enable Transport, your system will route traffic
|
||||
# for other peers, pass announces and serve path requests.
|
||||
# This should be done for systems that are suited to act
|
||||
# as transport nodes, ie. if they are stationary and
|
||||
# always-on. This directive is optional and can be removed
|
||||
# for brevity.
|
||||
|
||||
enable_transport = False
|
||||
|
||||
|
||||
# By default, the first program to launch the Reticulum
|
||||
# Network Stack will create a shared instance, that other
|
||||
# programs can communicate with. Only the shared instance
|
||||
# opens all the configured interfaces directly, and other
|
||||
# local programs communicate with the shared instance over
|
||||
# a local socket. This is completely transparent to the
|
||||
# user, and should generally be turned on. This directive
|
||||
# is optional and can be removed for brevity.
|
||||
|
||||
share_instance = Yes
|
||||
|
||||
|
||||
# If you want to run multiple *different* shared instances
|
||||
# on the same system, you will need to specify different
|
||||
# shared instance ports for each. The defaults are given
|
||||
# below, and again, these options can be left out if you
|
||||
# don't need them.
|
||||
|
||||
shared_instance_port = 37428
|
||||
instance_control_port = 37429
|
||||
|
||||
# You can configure Reticulum to panic and forcibly close
|
||||
# if an unrecoverable interface error occurs, such as the
|
||||
# hardware device for an interface disappearing. This is
|
||||
# an optional directive, and can be left out for brevity.
|
||||
# This behaviour is disabled by default.
|
||||
|
||||
panic_on_interface_error = No
|
||||
|
||||
|
||||
[logging]
|
||||
# Valid log levels are 0 through 7:
|
||||
# 0: Log only critical information
|
||||
# 1: Log errors and lower log levels
|
||||
# 2: Log warnings and lower log levels
|
||||
# 3: Log notices and lower log levels
|
||||
# 4: Log info and lower (this is the default)
|
||||
# 5: Verbose logging
|
||||
# 6: Debug logging
|
||||
# 7: Extreme logging
|
||||
|
||||
loglevel = 4
|
||||
|
||||
|
||||
# The interfaces section defines the physical and virtual
|
||||
# interfaces Reticulum will use to communicate on. This
|
||||
# section will contain examples for a variety of interface
|
||||
# types. You can modify these or use them as a basis for
|
||||
# your own config, or simply remove the unused ones.
|
||||
|
||||
[interfaces]
|
||||
|
||||
# This interface enables communication with other
|
||||
# link-local Reticulum nodes over UDP. It does not
|
||||
# need any functional IP infrastructure like routers
|
||||
# or DHCP servers, but will require that at least link-
|
||||
# local IPv6 is enabled in your operating system, which
|
||||
# should be enabled by default in almost any OS. See
|
||||
# the Reticulum Manual for more configuration options.
|
||||
|
||||
[[Default Interface]]
|
||||
type = AutoInterface
|
||||
interface_enabled = True
|
||||
|
||||
|
||||
# The following example enables communication with other
|
||||
# local Reticulum peers using UDP broadcasts.
|
||||
|
||||
[[UDP Interface]]
|
||||
type = UDPInterface
|
||||
interface_enabled = False
|
||||
listen_ip = 0.0.0.0
|
||||
listen_port = 4242
|
||||
forward_ip = 255.255.255.255
|
||||
forward_port = 4242
|
||||
|
||||
# The above configuration will allow communication
|
||||
# within the local broadcast domains of all local
|
||||
# IP interfaces.
|
||||
|
||||
# Instead of specifying listen_ip, listen_port,
|
||||
# forward_ip and forward_port, you can also bind
|
||||
# to a specific network device like below.
|
||||
|
||||
# device = eth0
|
||||
# port = 4242
|
||||
|
||||
# Assuming the eth0 device has the address
|
||||
# 10.55.0.72/24, the above configuration would
|
||||
# be equivalent to the following manual setup.
|
||||
# Note that we are both listening and forwarding to
|
||||
# the broadcast address of the network segments.
|
||||
|
||||
# listen_ip = 10.55.0.255
|
||||
# listen_port = 4242
|
||||
# forward_ip = 10.55.0.255
|
||||
# forward_port = 4242
|
||||
|
||||
# You can of course also communicate only with
|
||||
# a single IP address
|
||||
|
||||
# listen_ip = 10.55.0.15
|
||||
# listen_port = 4242
|
||||
# forward_ip = 10.55.0.16
|
||||
# forward_port = 4242
|
||||
|
||||
|
||||
# This example demonstrates a TCP server interface.
|
||||
# It will listen for incoming connections on the
|
||||
# specified IP address and port number.
|
||||
|
||||
[[TCP Server Interface]]
|
||||
type = TCPServerInterface
|
||||
interface_enabled = False
|
||||
|
||||
# This configuration will listen on all IP
|
||||
# interfaces on port 4242
|
||||
|
||||
listen_ip = 0.0.0.0
|
||||
listen_port = 4242
|
||||
|
||||
# Alternatively you can bind to a specific IP
|
||||
|
||||
# listen_ip = 10.0.0.88
|
||||
# listen_port = 4242
|
||||
|
||||
# Or a specific network device
|
||||
|
||||
# device = eth0
|
||||
# port = 4242
|
||||
|
||||
|
||||
# To connect to a TCP server interface, you would
|
||||
# naturally use the TCP client interface. Here's
|
||||
# an example. The target_host can either be an IP
|
||||
# address or a hostname
|
||||
|
||||
[[TCP Client Interface]]
|
||||
type = TCPClientInterface
|
||||
interface_enabled = False
|
||||
target_host = 127.0.0.1
|
||||
target_port = 4242
|
||||
|
||||
|
||||
# This example shows how to make your Reticulum
|
||||
# instance available over I2P, and connect to
|
||||
# another I2P peer. Please be aware that you
|
||||
# must have an I2P router running on your system
|
||||
# with the SAMv3 API enabled for this to work.
|
||||
|
||||
[[I2P]]
|
||||
type = I2PInterface
|
||||
interface_enabled = yes
|
||||
peers = 5urvjicpzi7q3ybztsef4i5ow2aq4soktfj7zedz53s47r54jnqq.b32.i2p
|
||||
|
||||
|
||||
# Here's an example of how to add a LoRa interface
|
||||
# using the RNode LoRa transceiver.
|
||||
|
||||
[[RNode LoRa Interface]]
|
||||
type = RNodeInterface
|
||||
|
||||
# Enable interface if you want use it!
|
||||
interface_enabled = False
|
||||
|
||||
# Serial port for the device
|
||||
port = /dev/ttyUSB0
|
||||
|
||||
# Set frequency to 867.2 MHz
|
||||
frequency = 867200000
|
||||
|
||||
# Set LoRa bandwidth to 125 KHz
|
||||
bandwidth = 125000
|
||||
|
||||
# Set TX power to 7 dBm (5 mW)
|
||||
txpower = 7
|
||||
|
||||
# Select spreading factor 8. Valid
|
||||
# range is 7 through 12, with 7
|
||||
# being the fastest and 12 having
|
||||
# the longest range.
|
||||
spreadingfactor = 8
|
||||
|
||||
# Select coding rate 5. Valid range
|
||||
# is 5 throough 8, with 5 being the
|
||||
# fastest, and 8 the longest range.
|
||||
codingrate = 5
|
||||
|
||||
# You can configure the RNode to send
|
||||
# out identification on the channel with
|
||||
# a set interval by configuring the
|
||||
# following two parameters. The trans-
|
||||
# ceiver will only ID if the set
|
||||
# interval has elapsed since it's last
|
||||
# actual transmission. The interval is
|
||||
# configured in seconds.
|
||||
# This option is commented out and not
|
||||
# used by default.
|
||||
# id_callsign = MYCALL-0
|
||||
# id_interval = 600
|
||||
|
||||
# For certain homebrew RNode interfaces
|
||||
# with low amounts of RAM, using packet
|
||||
# flow control can be useful. By default
|
||||
# it is disabled.
|
||||
flow_control = False
|
||||
|
||||
|
||||
# An example KISS modem interface. Useful for running
|
||||
# Reticulum over packet radio hardware.
|
||||
|
||||
[[Packet Radio KISS Interface]]
|
||||
type = KISSInterface
|
||||
|
||||
# Enable interface if you want use it!
|
||||
interface_enabled = False
|
||||
|
||||
# Serial port for the device
|
||||
port = /dev/ttyUSB1
|
||||
|
||||
# Set the serial baud-rate and other
|
||||
# configuration parameters.
|
||||
speed = 115200
|
||||
databits = 8
|
||||
parity = none
|
||||
stopbits = 1
|
||||
|
||||
# Set the modem preamble. A 150ms
|
||||
# preamble should be a reasonable
|
||||
# default, but may need to be
|
||||
# increased for radios with slow-
|
||||
# opening squelch and long TX/RX
|
||||
# turnaround
|
||||
preamble = 150
|
||||
|
||||
# Set the modem TX tail. In most
|
||||
# cases this should be kept as low
|
||||
# as possible to not waste airtime.
|
||||
txtail = 10
|
||||
|
||||
# Configure CDMA parameters. These
|
||||
# settings are reasonable defaults.
|
||||
persistence = 200
|
||||
slottime = 20
|
||||
|
||||
# You can configure the interface to send
|
||||
# out identification on the channel with
|
||||
# a set interval by configuring the
|
||||
# following two parameters. The KISS
|
||||
# interface will only ID if the set
|
||||
# interval has elapsed since it's last
|
||||
# actual transmission. The interval is
|
||||
# configured in seconds.
|
||||
# This option is commented out and not
|
||||
# used by default.
|
||||
# id_callsign = MYCALL-0
|
||||
# id_interval = 600
|
||||
|
||||
# Whether to use KISS flow-control.
|
||||
# This is useful for modems that have
|
||||
# a small internal packet buffer, but
|
||||
# support packet flow control instead.
|
||||
flow_control = false
|
||||
|
||||
|
||||
# If you're using Reticulum on amateur radio spectrum,
|
||||
# you might want to use the AX.25 KISS interface. This
|
||||
# way, Reticulum will automatically encapsulate it's
|
||||
# traffic in AX.25 and also identify your stations
|
||||
# transmissions with your callsign and SSID.
|
||||
#
|
||||
# Only do this if you really need to! Reticulum doesn't
|
||||
# need the AX.25 layer for anything, and it incurs extra
|
||||
# overhead on every packet to encapsulate in AX.25.
|
||||
#
|
||||
# A more efficient way is to use the plain KISS interface
|
||||
# with the beaconing functionality described above.
|
||||
|
||||
[[Packet Radio AX.25 KISS Interface]]
|
||||
type = AX25KISSInterface
|
||||
|
||||
# Set the station callsign and SSID
|
||||
callsign = NO1CLL
|
||||
ssid = 0
|
||||
|
||||
# Enable interface if you want use it!
|
||||
interface_enabled = False
|
||||
|
||||
# Serial port for the device
|
||||
port = /dev/ttyUSB2
|
||||
|
||||
# Set the serial baud-rate and other
|
||||
# configuration parameters.
|
||||
speed = 115200
|
||||
databits = 8
|
||||
parity = none
|
||||
stopbits = 1
|
||||
|
||||
# Whether to use KISS flow-control.
|
||||
# This is useful for modems with a
|
||||
# small internal packet buffer.
|
||||
flow_control = false
|
||||
|
||||
# Set the modem preamble. A 150ms
|
||||
# preamble should be a reasonable
|
||||
# default, but may need to be
|
||||
# increased for radios with slow-
|
||||
# opening squelch and long TX/RX
|
||||
# turnaround
|
||||
preamble = 150
|
||||
|
||||
# Set the modem TX tail. In most
|
||||
# cases this should be kept as low
|
||||
# as possible to not waste airtime.
|
||||
txtail = 10
|
||||
|
||||
# Configure CDMA parameters. These
|
||||
# settings are reasonable defaults.
|
||||
persistence = 200
|
||||
slottime = 20
|
||||
|
||||
'''
|
||||
|
||||
if __name__ == "__main__":
|
||||
main()
|
||||
main()
|
||||
|
||||
Loading…
Reference in New Issue
Block a user